Hardware sold separately. Cross-section & dimension callouts shown in the technical data below.
Insulated Pipe Support · With Load Distribution Plate
A5000
A medium-to-heavy-duty, pre-insulated pipe support for hot, cold, and chilled lines – with an integral load distribution plate on the bottom jacket, for use on flat surfaces and pipe rolls without welding to the pipe.
Talk to a pipe support specialist about your application.
1-707-447-5014General Dimensions & Specifications
Hardware sold separately
Note: For higher load ratings, see A7000
| Oper. Temp. °F |
Mult. Factor “F” |
|---|---|
| 500 | 0.90 |
| 750 | 0.75 |
| 1000 | 0.50 |
| 1200 | 0.30 |
| TABLE II | |
| Pipe Size |
MAXIMUM LOAD RATING (LBS) |
A | B | C | Max. Axial Travel (inches) on Pipe Roll +/- |
|
|---|---|---|---|---|---|---|
| On Flat Surface (a) (b) |
On Pipe Roll (b) |
|||||
| 2 1/2 | 200 | 180 | 9 | 6 | 1/4 | 2 |
| 3 | 250 | 225 | 9 | 6 | 1/4 | 2 |
| 3 1/2 | 300 | 270 | 9 | 6 | 1/4 | 2 |
| 4 | 350 | 315 | 9 | 6 | 1/4 | 2 |
| 5 | 450 | 400 | 9 | 6 | 1/4 | 2 |
| 6 | 500 | 450 | 9 | 6 | 1/4 | 2 |
| 8 | 625 | 550 | 9 | 6 | 1/4 | 2 |
| 10 | 650 | 575 | 9 | 6 | 1/4 | 2 |
| 12 | 925 | 825 | 12 | 9 | 3/8 | 3 |
| 14 | 1000 | 900 | 12 | 9 | 3/8 | 3 |
| 16 | 1100 | 975 | 12 | 9 | 1/2 | 3 |
| 18 | 1200 | 1075 | 12 | 9 | 1/2 | 3 |
| 20 | 1300 | 1150 | 12 | 9 | 1/2 | 3 |
| 24 | 1400 | 1250 | 12 | 9 | 3/4 | 3 |
| 30 | 1500 | 1350 | 12 | 9 | 3/4 | 3 |
| 36 | 1500 | 1350 | 12 | 9 | 3/4 | 3 |
| 42 | 1500 | 1350 | 12 | 9 | 3/4 | 3 |
| TABLE I | ||||||
Contact factory for other dimensions, temperatures, and loads.
Available in all insulation thicknesses.
The load ratings represent average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations. Dimensions and ratings are subject to change without notice. Contact factory for current information.
a) To develop maximum load rating, width of support surface should be at least 1/2 of dimension “B” in Table I.
b) To obtain load ratings for operating temperatures of 500°F and higher, multiply maximum load rating by factor “F” in Table II.
Application
Model A5000 is designed for use on:
- Hot water
- Cold water
- Chilled water
- Dual temperature
- Steam
- Air
- Gas
- Vacuum
Intended for installation on:
- Flat surfaces
- Pipe rolls
Temperature Range
Standard: +40°F to +1200°F CalSil Insulation
Note: Up to 1800°F available upon request.
Cryogenic: -275°F to +275°F Urethane Insulation.
Add U after the model number (i.e., A5000U)
Features
- Compact
- Easy installation
- Eliminates welding to pipe
- Copper tubing sizes available
- Overlapping galvanized sheet metal jacket
- Minimizes heat loss and/or condensation
- Load distribution plate integral with bottom jacket
- Other I.D.’s and/or O.D.’s available on request
Material Data
| A5000 Spec Doc | Applicable PSI spec. doc.: No. 205 |
|---|---|
| Insulation | Calcium silicate, asbestos-free, treated with water repellant |
| Jackets | Galvanized steel, ASTM A-653 |
| Load Distribution Plate | Carbon steel ASTM A-36 |
| Coating | Primer coated or hot-dip galvanized. Other coatings available upon request. |
| Glue | Industrial contact adhesive |
Installation Guide
Model A1000 – A4000 & A9000
1. Position the bottom half of the insulated hanger shield (insulating structural material, sheet metal jacket and load plate where applicable) on the pipe at the applicable support location as shown.
2. Hold the top half of the shield firmly. Open the overlapping sheet metal jacket and gently slide into position the top half of the insulated shield over the bottom half shield as shown.
Model A5000 – A8400
1. When used on a flat surface, position shield so that it is centered on the structural steel.
2. When used with a clevis hanger, position shield symmetrically.
3. When models include heat trace groves, the number and location may vary. Check with design drawings for exact number and location. Ensure that the heat tracing cable is properly positioned inside the grove of the shield.
Completed Assembly Without Load Plate
Completed Assembly With Load Plate
Downloads & resources
Custom Design Request
Need other I.D.'s, O.D.'s, temperatures or loads? Submit a custom design request.
Start Request →Revit RFA 3D Model
A1000 Insulated Pipe Support Revit RFA model for BIM & coordination workflows.
Download 3D Model →